LEAVE A MESSAGE
Shenzhen E-5continents Co., Ltd Powered by:www.300.cn 粤ICP备05044687号-4
CONTACT US
Shenzhen E-5continents Co., Ltd
Tel.:+86 755 26086046 / 26088742
E-mail:sales2@e-5continents.com sale6@e-5continents.com
Address: 4th Floor Building B2, Sunshine Industrial Zone,Hezhou,
Xixiang, Bao an District, Shenzhen, China
Outdoor siren with strobe 5C-121
Installation and User Manual
Outdoor Siren
Specification
The outdoor siren is a new generation of professional high power acoustic siren with battery
back-up and flashlight, which includes all performance and reliability for security alarm system
Features:
♦Outdoor battery back-up siren with flashlight.
♦Double housing: external 3mm plastic ABS with UV9 internal 0.8mm metal.
♦Continuous frequency modulated sound.
♦Tamper protection in 3 ways — screw or cover opening or tearing housing from the wall.
♦Positive and negative alarm trigger input.
♦Trigger input to active only the flashlight.
♦Siren period can set as follow trigger or 3 min cutoff
♦Select from the lamp or xenon
♦Alarm by main power failure
♦Protecting against totally battery discharge
♦Plug terminal for easy installation.
♦Environmental immunity
Functional Description Alarm Trigger
Applying high or low voltage to the “GO+” or “GO-” inputs terminals respectively can trigger
the alarm. The sound and flashlight triggered together. Alarm siren duration depended on the
trigger selector state.
♦F.T - Follow Trigger.
♦TMR-siren cutoff after 3 minutes, this state is recommended in order to avoid violation
of any local regulations.
Flash Trigger:
Applying “low” level to “FL-”terminal can trigger the flashlight. Flashlight duration is not
limited and the time of flashlight is set by control panel-as long as trigger available the
flashlight will be active.
Tamper:
The tamper is normally closed while the housing is closed with the screw, so in this
state the tamper terminals are shorted (0 ohm).The tamper will open while opening
the screw the tamper socket to the wall properly.
Power Failure:
On power failure the siren and flashlight are triggering, until power supply is restored
or time out (5 minutes) expires.
Battery Protection:
The siren is supplied with protection against totally battery discharge by cutting off the
siren, when voltage level falls down to less then 8VDC.
Installation instructions
1. Choose the mounting location for the siren-the wall must be even and free of hole and
excessive protrusions.
Note: Take a consideration about the wires inputs in the housing base.
2. Mark and drill 5 holes with help of attach drill pattern plate (4 holes for the housing based
and 1 for the tamper).
Important: Cut off the power before you make the connection
3. Open the siren housing (1 screw on the front), fig1 and remove the metal cover (2 screws),
fig2
4. Unplug the terminal 5 on the siren driver Mount the siren housing on the wall Connect the
wires to the terminal 5
5. Plug the terminal to your drive board.
6. Power on the system and check its function properly
Important: keep attention the polarity of the battery; a reverse polarity can cause damage of
the driver circuit.
7.Connect the back-up battery
8. Mount the metal cover with 2 screws
9. Close the housing with 1 screw.
Terminal Block Connection
Terminal 1 -Marked “FL-” trigger for the flashlight connect it to output in the alarm system, Active
while the input is low.
Terminal 2- Marked “Go+” trigger for the siren and the flashlight, Active while the input is high.
Terminal 3-Marked ‘‘GO-’’ trigger for the siren and flashlight, active while the input is low.
Terminal 4-Marked the “GND”connect to the ground of the control unit.
Terminal 5-Marked “+12 V”connect to a positive voltage output of the 13.6-14.2 VDC source
(usually from the alarm control unit).
Terminal 6&7-Marked “Temper” if a tamper function is required connect these terminals to
a 24-hour normally closed the protective zone in the control unit, if the front cover of the siren
is opened or siren box is tearing from the wall, an immediate alarm signal will be sent to the
control unit
Specification |
|
SPL |
120db |
Fundamental Frequency |
1850Hz |
Siren Tone |
Yelp |
Frequency Range |
1300-2400Hz |
Flashlight |
Lamp J2VDC/5W |
Power supply Voltage |
13.8-14.2VDC |
Charge Current Limit |
250mA |
Current Consumption |
Standby: 8mA |
(Speaker and strobe) |
Alarm 1600mA@13.8VDC |
Maximum Power |
50W(peak) |
Trigger Level |
Trigger Low=Max .1VDC, Trigger High=Min.9VDC |
Siren Alarm Period |
F.T-Follow trigger / TMR-3 min |
Input Impedance(Alarm/Flash/Trigger) |
IK ohm |
Tamper Switch |
N.C 28VDC Maximum current O.lA-open when cover is removed |
Backup Battery |
Rechargeable Lead Acid Battery 12VDC up to 7.2Ah |
Low Battery Level |
8VDC+/-0.3VDC |
Material |
External Box: ABS (3mm Thickness), Internal cover: metal (0.8mm thickness) |
Dimensions of Unit |
L =270mm* W= 193mm*H= 100 mm |
Weight(without battery) |
1.85Kg |
Operating Temperature Range |
-30 to +60 °C |
Case Protection Level |
Water splash resistant / Plastic ABS with UV Protection/ Conformal coated circuit board |